![\"Head](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2019\/02\/f72dda6d6b18ec8efbbdc1b668f25f04-600x450.jpg\")
<\/p>\nHello, everyone.<\/p>\n
This is Enta.<\/p>\n
The rain we had the other day\u2014our first in a while\u2014made my pollen allergy symptoms a lot better, but,<\/p>\n
As it gradually gets warmer, things are probably going to turn into hell, lol.<\/p>\n
If only there weren't any pollen, it would be perfect...<\/p>\n
But that's beside the point.<\/p>\n
This is a continuation of my previous post.<\/p>\n
We take a very strict approach to installing the head unit.<\/p>\n
As shown in the figure below, the protrusion varies depending on the thickness of the compression member.<\/p>\n
Be sure to check the thickness of the load-bearing plate and manage the projection of the apartment building.<\/p>\n
<\/p>\n
You might think it\u2019s generally best to follow the design as intended, but there\u2019s actually a pitfall here.<\/p>\n
Especially when there\u2019s just one wire, like in this diagram, it tends to stretch quite a bit.<\/p>\n
With that in mind, installing it about 1\u20132 cm lower can sometimes result in a nice, neat fit.<\/p>\n
<\/p>\n
That means you need to understand the theoretical performance gains before installing it.<\/p>\n
Please be sure to do the calculations.<\/p>\n
Load-bearing plate + angle adjustment base (if necessary) + reinforcing steel plate + amount of elongation during installation = amount by which the head protrudes<\/strong><\/span><\/p>\n And, just to confirm,As long as it's shorter than the depth of the cap, it's fine.<\/span><\/strong><\/span><\/p>\n What if the apartment building sticks out too far, as shown in the figure above?<\/p>\n Since the apartment building has PC steel strands embedded within its structure, cutting it could cause the building itself to collapse.<\/p>\n Therefore, cutting is not permitted.<\/p>\n As a countermeasure, it\u2019s probably safest to just raise the structure that\u2019s under pressure, lol.<\/p>\n Since it would be very difficult to lift the load-bearing plate itself, you can add another steel plate as reinforcement.<\/p>\n Now, let's consider a situation where the condominium has few units.<\/p>\n In a situation like this, where the mountain is sliding down, this is what happens when the mountain pushes forward.<\/p>\n Also, if the anchor body slips down due to some kind of mistake, this is what happens!<\/p>\n So, what should we do in that case!?<\/p>\n <\/p>\n See you later.<\/p>","protected":false},"excerpt":{"rendered":" Hello, everyone. It\u2019s Enta here. The rain we had the other day\u2014our first in a while\u2014made the pollen situation a lot more bearable, but as it gradually gets warmer, it\u2019s probably going to turn into hell lol. It would be perfect if only there weren\u2019t any pollen\u2026 Anyway, back to where we left off the other day. Installing the head module is a pretty precise process\u2026<\/p>","protected":false},"author":2,"featured_media":38462,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_bbp_topic_count":0,"_bbp_reply_count":0,"_bbp_total_topic_count":0,"_bbp_total_reply_count":0,"_bbp_voice_count":0,"_bbp_anonymous_reply_count":0,"_bbp_topic_count_hidden":0,"_bbp_reply_count_hidden":0,"_bbp_total_topic_count_hidden":0,"_bbp_total_reply_count_hidden":0,"_bbp_forum_subforum_count":0,"footnotes":"","jetpack_post_was_ever_published":false},"categories":[28],"tags":[48,114,262,2173,2174,2175,2176],"class_list":["post-38464","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-ground-anchor","tag-48","tag-114","tag-262","tag-seee","tag-2174","tag-2175","tag-2176"],"acf":[],"yoast_head":"\n![\"Too](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2019\/02\/944c344ca112a301739033ac7df208a1-600x450.jpg\")
<\/p>\n![\"Few](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2019\/03\/11cc65ac19ae3ba7d24aa17a08fc7636-600x450.jpg\")
<\/p>\n