\n
![\"Labor](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2016\/11\/3637db97c20ba5c356e338f1921c42fd.jpg\")
<\/p>\nHello, everyone.<\/p>\n
This is Enta.<\/p>\n
It's time for the labor cost survey.
\n <\/p>\n
This is such a hassle, too. The office staff, lol.<\/p>\n
I grumble about this every year. The office staff, lol<\/p>\n
Plus, since I get accepted to several places at once, I end up turning down a bunch of them to go to just one\u2014but honestly, it\u2019s a hassle.<\/p>\n
I\u2019m thinking, why don\u2019t we use Construction CALS and ICT to do this online?<\/p>\n
Some kind of vested interest... ?<\/p>\n
But that's beside the point.<\/p>\n
It's only been about a week since the blog was migrated.<\/p>\n
Actually, the site itself isn't finished yet; I just went ahead and launched it in a state where it can at least be operated for now.<\/p>\n
I think it'll gradually stick to the side, but here's what I attached the other day.<\/p>\n
Did you notice? lol<\/p>\n
![\"Grout](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2016\/11\/ec70e4b2523933fe48d786fef617d56c.jpg\")
<\/p>\n
I'd like to explain this in this post.<\/p>\n
This is what the site looks like when you open it.<\/p>\n
![\"Grout](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2016\/11\/d44245530931eeba1755d5d106f7c474.jpg\")
<\/p>\n
I'll go through them in order, starting with \u2460.<\/p>\n
\u2460 Select the nominal drilling diameter.<\/strong><\/span><\/p>\n For example, a borehole diameter of 90 mm is equivalent to 0.09 m.<\/p>\n The unit is meters.<\/p>\n <\/p>\n \u2461 Enter the drilling depth.<\/strong><\/span><\/p>\n If the drilling length per hole is 4.0 m, then it is 4.0 m.<\/p>\n That's exactly right.<\/p>\n Please note that for formwork, the designed drilling depth is calculated after subtracting the width of the formwork.<\/p>\n <\/p>\n \u2462 The loss rate.<\/strong><\/span><\/p>\n It varies depending on the mountain, but I think using the same loss rate as in the design should be fine.<\/p>\n For example, 3.2.<\/p>\n <\/p>\n \u2463 Number of piles driven.<\/strong><\/span><\/p>\n If the design calls for 100, then it's 100, lol.<\/p>\n <\/p>\n \u2464 The amount of cement per cubic meter.<\/span><\/strong><\/p>\n As usual, 1,230 kg is fine.<\/p>\n If you want to increase or decrease the amount of cement, please enter the amount here.<\/p>\n <\/p>\n \u2465 The amount of cement per bag.<\/span><\/strong><\/span><\/p>\n A standard bag of cement weighs 25 kg.<\/p>\n Is that 900 kg for a flexible container bag?<\/p>\n <\/p>\n \u2466 Press this to calculate.<\/strong><\/span><\/p>\n \u2467 Automatically enters the actual diameter of the borehole specified in step \u2460.<\/span><\/strong><\/span><\/p>\n If you uncheck this box, you will not enter the actual drilling diameter.<\/p>\n \u2468 If the value is not automatically entered in \u2467, please enter it here in meters.<\/strong><\/span><\/p>\n That's all.<\/p>\n <\/p>\n What this means is that the design quantity differs from the actual order quantity.<\/p>\n The design dimensions are based on the nominal diameter, but since the actual diameter is larger, there is a difference.<\/p>\n Wouldn't it be a problem if we included that in the design during the budgeting process?<\/p>\n <\/p>\n As an extreme example,<\/p>\n Drill hole diameter: 90 mm<\/strong><\/p>\n Drilling depth: 2,000 m<\/strong><\/p>\n Quantity: 1<\/strong><\/p>\n Loss ratio: 3.2 times<\/strong><\/p>\n There might actually be 400 pieces that are 5 meters long, but as long as I know the total, that's all I need.<\/p>\n That's how you can use it, as shown above.<\/p>\n \n Based on the above calculation, there\u2019s a difference of about 600 bags of cement between the design quantity and the actual quantity.<\/p>\n I just made this to get a quick grasp of this area lol<\/p>\n By the way, the same goes for the bottom section\u2014you can perform all three types of calculations at once, and<\/strong><\/p>\n I've set it up so that the total appears at the very bottom.<\/strong><\/p>\n <\/p>\n Well, that's it for now.<\/p>\n *Please use this only if you understand it and are willing to assume full responsibility for your actions.<\/strong><\/span><\/p>","protected":false},"excerpt":{"rendered":" Hello, everyone. This is Enta. It\u2019s that time of year again for the labor cost survey. This is such a hassle. The office staff\u2026 lol. They grumble about it every year. The office staff, lol. Plus, since we get assigned to several locations at once, we end up turning down a bunch of them and only going to one\u2014but honestly, it\u2019s a pain. Construction CALS, and\u2026<\/p>","protected":false},"author":2,"featured_media":1649,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"_bbp_topic_count":0,"_bbp_reply_count":0,"_bbp_total_topic_count":0,"_bbp_total_reply_count":0,"_bbp_voice_count":0,"_bbp_anonymous_reply_count":0,"_bbp_topic_count_hidden":0,"_bbp_reply_count_hidden":0,"_bbp_total_topic_count_hidden":0,"_bbp_total_reply_count_hidden":0,"_bbp_forum_subforum_count":0,"footnotes":"","jetpack_post_was_ever_published":false},"categories":[38],"tags":[44,48,49,58,59],"class_list":["post-1645","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-construction-management","tag-44","tag-48","tag-49","tag-58","tag-59"],"acf":[],"yoast_head":"\n![\"Grout](\"https:\/\/norimen.net\/wordpress\/wp-content\/uploads\/2016\/11\/1087c2b54ea1872e3083aa504c56c7f1.jpg\")
<\/p>\n